DEV(10.2) DEV(10.2)
NAME
Dev - device driver interface
SYNOPSIS
struct Dev
{
int dc;
char* name;
void (*reset)(void); /* native only */
void (*init)(void);
void (*shutdown)(void); /* native */
Chan* (*attach)(char *spec);
Walkqid* (*walk)(Chan *c, Chan *nc, char **name, int nname);
int (*stat)(Chan *c, uchar *db, int dbsize);
Chan* (*open)(Chan *c, int mode);
void (*create)(Chan *c, char *name, int mode, ulong perm);
void (*close)(Chan *c);
long (*read)(Chan *c, void *buf, long nbytes, vlong offset);
Block* (*bread)(Chan *c, long nbytes, ulong offset);
long (*write)(Chan *c, void*, long, vlong offset);
long (*bwrite)(Chan *c, Block *b, ulong offset);
void (*remove)(Chan *c);
int (*wstat)(Chan *c, uchar *db, int dbsize);
void (*power)(int on); /* native only */
int (*config)(int on, char *spec, DevConf *cf); /* native */
};
DESCRIPTION
Every device driver serves a unique name space that
represents to the corresponding device(s). Applications act
on the space using the operations of sys-bind(2), sys-
open(2), sys-read(2), sys-stat(2), and other system calls.
Within the kernel, the Dev structure defines the interface
between the kernel and a device driver for all operations on
that driver's name space.
Dev identifies the driver, and lists a set of C functions
that are the driver's operations. Most are operations on
the Chan type that is the kernel representation of a file or
directory active in a name space. The kernel converts sys-
tem calls acting on file descriptors into calls to a
device's Dev operations acting on channel values. All chan-
nel values presented through the Dev interface are associ-
ated with the corresponding device driver: for channel c,
c->type specifies that driver. Within the driver, the
c->qid.path of a channel c identifies a file in the driver's
name space, or even a client-specific instance of a file
(eg, for multiplexors such as ip(3)). The interpretation of
the path is completely determined by the driver.
Page 1 Plan 9 (printed 12/19/25)
DEV(10.2) DEV(10.2)
A device driver in the source file devx.c exports an ini-
tialised instance of Dev xdevtab. For instance, devcons.c
contains the global initialiser:
Dev consdevtab = {
'c',
"cons",
devreset,
consinit,
devshutdown,
consattach,
conswalk,
consstat,
consopen,
devcreate,
consclose,
consread,
devbread,
conswrite,
devbwrite,
devremove,
devwstat,
};
The kernel accesses the driver only through its Dev struc-
ture, and consequently entry points such as consinit,
consread, etc. can (and should) be declared static, and thus
local to the file.
The following elements of Dev identify the driver:
dc The device's type, represented by a Unicode character
(`rune') that must be unique amongst those in a given
kernel (and ideally for a given platform). Its value
is the value of Dir.dtype in the result of a sys-
stat(2) applied to any file in the device.
name The name that identifies the driver in a kernel config-
uration file and in /dev/drivers (see cons(3)).
All the other entries are functions. In many cases, the
values given in a device's Dev will be the default opera-
tions provided by devattach(10.2).
reset()
Called once during system initialisation by the native
kernel's main after initialising all supporting subsys-
tems, including memory allocation, traps, screen, MMU
(if used), but with interrupts disabled, and before any
kernel process environment has been established. Typi-
cally used on some platforms to force some devices into
Page 2 Plan 9 (printed 12/19/25)
DEV(10.2) DEV(10.2)
a sane state before interrupts are enabled.
init()
Called once during system initialisation in the context
of the first kernel process, with interrupts enabled,
before the virtual machine has been started.
shutdown()
Called once in native kernels during system shut down.
Used on only a few platforms to force a device into a
state that will allow it to function correctly during
and after a soft reboot (eg, without doing a full sys-
tem hardware reset).
attach(spec)
Called on each new attach to the device (eg, a refer-
ence to #c by sys-bind(2)). Spec is the string follow-
ing the device character and before a subsequent `/' in
the bind request. It is the empty string for most
devies. If the attach is successful, attach should
return a Chan the refers to the root of the tree served
by the device driver. Normally, it will suffice to
return the value of devattach(10.2).
walk(c, nc, name, nname)
Walks existing channel c from its current position in
the device tree to that specified by the path repre-
sented by name[0], ... name[nname-1]. The driver must
interpret `..' as a walk from the current position one
level up towards the root of the device tree. The
result is represented by a dynamically-allocated
Walkqid value, with contents as described in
devattach(10.2). Most drivers simply pass parameters on
to devwalk in devattach(10.2) and return its result.
stat(c, db, nbytes)
Fill db with stat(5) data describing the file refer-
enced by c. Nbytes gives the size of db; if the data
will not fit, return the value specified for convD2M in
styx(10.2). Most drivers simply pass parameters on to
devstat in devattach(10.2); a few fill a local copy of
a Dir structure, and call convD2M to store the
machine-independent representation in db.
open(c, mode)
Open the file represented by Chan c, in the given mode
(see sys-open(2)), and if successful, return a Chan
value representing the result (usually c). Many drivers
simply apply devopen of devattach(10.2). Exclusive use
drivers might check and increment a reference count.
create(c, name, mode, perm)
Page 3 Plan 9 (printed 12/19/25)
DEV(10.2) DEV(10.2)
C should be a directory. Create a new file name in
that directory, with permissions perm, opened with the
given mode. If successful, make c refer to the newly
created file. Most drivers return an error on all cre-
ation attempts, by specifying devcreate of
devattach(10.2) in the Dev table.
close(c)
Close channel c. This must be implemented by all
drivers; there is no default, although the function
often is a no-op. Exclusive use drivers might decre-
ment a reference count.
read(c, buf, nbytes, offset)
Implement a sys-read(2) of nbytes of data from the
given offset in file c, and if successful, place the
data in buf, and return the number of bytes read, which
must be no greater than nbytes. Devices sometimes
ignore the offset. All device drivers must implement
read; there is no default. Note that if c is a direc-
tory, the data has an array of stat(5) data listing the
directory contents, in the format prescribed by
read(5). Most drivers have devdirread of
devattach(10.2) do the work when c is the root direc-
tory of the device's tree.
bread(c, nbytes, offset)
Implement a sys-read(2) of nbytes of data from the
given offset in file c, and if successful return the
data in a Block (see allocb(10.2) and qio(10.2)). Most
drivers use the default devbread provided by
devattach(10.2), and nearly all ignore the offset in
any case. Drivers that manipulate Blocks internally,
such as ip(3), ssl(3) and similar protocol devices, and
drivers that are likely to provide data to those
devices, will provide a devbread implementation so as
to reduce the number of times the data is copied.
write(c, buf, nbytes, offset)
Implement a write of nbytes of data from buf to file c,
which must not be a directory, starting at the given
byte offset. Return the number of bytes actually writ-
ten. There is no default, but drivers that do not
implement writes to any of their files can simply call
error(Eperm) to signal an error.
bwrite(c, b, offset)
Similar to the write entry point, but the data is con-
tained in a Block b (see allocb(10.2)). B should be
freed before return, whether the driver signals an
error or not. Most drivers use the default devbwrite
from devattach(10.2), which calls the driver's write
Page 4 Plan 9 (printed 12/19/25)
DEV(10.2) DEV(10.2)
entry point using the data in b. Drivers that manipu-
late Blocks internally, such as ip(3), ssl(3) and simi-
lar protocol devices, will provide a devbwrite imple-
mentation so as to avoid copying the data needlessly.
remove(c)
Remove the file referenced by c. Most drivers raise an
error by using the default devremove from
devattach(10.2).
wstat(c, db, dbsize)
Change the attributes of file c, using the stat(5) data
in buffer db, which is dbsize bytes long. Usually a
driver will use convM2D of styx(10.2) to convert the
data to a Dir structure, then apply the rules of
stat(5) to decide which attributes are to be changed
(and whether the change is allowed). Most drivers sim-
ply return an error on all wstat requests by using the
default devwstat from devattach(10.2).
power(on)
Reserved for use in native kernels, to allow the kernel
to power the device on and off for power-saving; on is
non-zero if the device is being powered up, and zero if
it is being powered down. The device driver should
save the device state if necessary. Leave the Dev
entry null for now.
config(on, spec, cf)
Reserved for use in native kernels to allow a device to
be configured on and off dynamically. Leave the Dev
entry null for now.
The elements reset, shutdown, power, and config are cur-
rently present only in the native kernels.
SEE ALSO
intro(2), intro(5), allocb(10.2), devattach(10.2),
newchan(10.2), qio(10.2)
Page 5 Plan 9 (printed 12/19/25)